Car Key Button Repair
A broken car key button can be frustrating. It is possible to call the 24 hour Locksmith Service or purchase an alternative remote.
You could be able to save money by fixing your old key fob instead of replacing it. This is particularly true if an old switch or damaged contacts are the reason for the problem.
Battery
If the buttons on your key fob are not responding to your pressing them, it could indicate that the battery has died or is about to reach the end of life. It's easy to replace the battery yourself instead of paying an auto locksmith or dealership.
First look for the battery compartment. It is typically located on the back of the key fob and may be hidden behind the cover, which slides out, or an access point which opens when you press the button. Once the compartment is opened you can see the small button battery. It is usually shaped like the shape of a coin and is has a plus and minus symbol. Remove the battery that is old and replace it with a new one. Check that the plus and the minus symbols are properly aligned.
Once the battery is installed Close the compartment and snap the two parts of the key fob. Before closing the door make sure to align and snap the pieces into place. Press go to website of the buttons to verify that they work properly.
If the remote keyfob doesn't work after replacing the battery, there could be other problems that require a different form of repair. The fob's dropping in a puddle could cause it to stop working. It could also be a problem with the internal electrical system or the need to be deprogrammed. Take a look at these other auto troubleshooting techniques to determine whether your key fob may be experiencing a different issue.
Switches
Depending on the year and the model, there are a variety of types of switches in the keyfob of your car. The older style key is equipped with an electronic chip that is visible in the case. The newer keys work by sending signals to your car. The buttons on a key may be damaged or worn out by regular use, irrespective of the type. The result is they become difficult to press or even ineffective. If you attempt to press the button too hard, it can cause further damage, and could even prevent the key from being able to start your vehicle in the future.
If you are unable to get your key to work, try changing the batteries. If it doesn't work, you may have to clean the key fob or adjust its switches. click to read are more likely than larger components of the key to break because they are constantly jostled.
The switches are made of rubber, and are coated with an electrically conducting film that wears down over time. Fortunately, they are also tiny and easy to replace. The older ones are soldered to the circuit board, and you'll need to be careful to remove them without causing any damage to anything else. Then you can solder in the new ones and reassemble your key fob.
Don't use your car key fob for more than a couple of hours at a stretch and avoid leaving it visible. When you're not using your key, keep it in a secure place.
If you've already tried cleaning your key fob or replacing the battery, and the issue continues to persist, it may be the right time to seek out a locksmith. A professional locksmith can test the frequency of your key to see if it's still able to communicate with your vehicle, and open and replace micro switches, change cases and much more.
Outer Case
If the buttons can't move freely up and down in the case, they may get stuck or break. If cleaning the case with rubbing alcohol and a cotton swab doesn't work, it may be necessary to take off the case. If the contacts that the buttons touch don't fit well or are worn out, adjusting them may be the only solution to correct the issue.
Some keys use buttons made of rubber, which be worn out over time. The buttons made of rubber can become difficult to press when they stretch, and nails could cut them. This could cause the key to fail and in this instance it's time for an entirely new case or buttons. This repair involves taking apart your remote, finding the switch on the board, then heating the solder and carefully remove them. The circuit board is then soldered with new buttons. The case is then rebuilt with the horse shoe key blade piece attached. The new buttons should be a close fit inside the case to avoid them from falling out.
Inner Case
Since your key fob is prone to get jostled around and may sometimes be accidentally pressed, the buttons inside can be damaged or stuck over time. Using metallic tape and a hole punch you can usually solve this issue in the event that your vehicle is not at home and the key fob won't work, allowing you to unlock the doors, but not start the engine. This simple fix can allow you to safely get back to your car and continue your journey.